Key takeaways
- Screw extractors bite into snapped bolts and stripped screws and back them out. Compare extractor sizes, drill pairings, case sets, and steel types.
As an Amazon Associate we earn from qualifying purchases.
A snapped bolt or a rounded-off screw head can stop a repair cold. The fastener will not turn with a driver, pliers slip on what is left of the head, and drilling the whole thing out risks damaging the threads in the part you are trying to save. Screw extractors exist for exactly this moment. Each one is a hardened tool that bites into the damaged fastener and turns it out in reverse, either after you drill a pilot hole or, in dual-ended designs, with a burnishing tip that prepares the head before the threaded end grips it.
The sets below cover the main extractor families a toolbox is likely to need: spiral flute extractors paired with left hand drill bits, hex head multi-spline extractors for high-torque work on studs and fittings, dual-ended drill-and-extract bits for stripped screw heads, external bolt extractor sockets that grip rounded nuts and lug nuts from the outside, and deep spiral extractors that reach fasteners seated below the surface. Sizes, piece counts, steel wording, and case details are stated exactly as the listings print them.
Disclosure: This article may contain affiliate links. If you buy through these links, we may earn a small commission from Amazon.
IRWIN Screw Extractor and Drill Bit Set, 10-Piece (11119)
This IRWIN HANSON set pairs five spiral flute extractors with five left hand cobalt drill bits, so the pilot hole and the extractor that follows it come from the same box. The extractors run from EX-1 through EX-5, and the fastener size and recommended drill bit size are etched directly onto each tool, which removes the guesswork when you are standing over a broken bolt with the drill already in hand. The spiral flutes use an aggressive left hand design: as you turn the extractor, the flutes embed themselves deeper into the metal, so gripping power grows as resistance increases. Because the drill bits are also left hand, drilling the pilot hole can sometimes loosen the fastener on its own before the extractor ever goes in. The listing states the tools are constructed of M-42, 8 percent cobalt, high speed steel for abrasive resistance in tough metals, and the set is housed in a metal index. It is aimed at broken studs, bolts, socket screws, and fittings.
Specs
- Set contents: 10 pieces — EX-1 through EX-5 spiral flute extractors plus matching left hand drill bits
- Material: M-42, 8 percent cobalt, high speed steel
- Markings: fastener size and recommended drill bit size etched on each tool
- Case: metal index
- Item weight: 0.4 pounds
- Item dimensions: 4.5 x 6.9 x 0.9 inches
- Cutting diameter: 0.25 inches
IRWIN Screw Extractor Set, Hex Head, Multi-Spline, 25-Piece (53227)
Where the 10-piece set works inside a drilled hole, this 25-piece IRWIN HANSON set takes a different approach to grip. Each extractor has a hex head that a wrench or socket can drive, and a multi-spline body that bites along the length of the hole rather than at a single tapered point. The listing says the set is designed to remove broken studs, bolts, socket screws, and fittings in high-torque applications, and the extractors are constructed of high carbon steel with an aggressive left hand spiral design for extra gripping power. Twenty-five sizes ranging from 1/8 inch to 7/8 inch give this set the widest spread in this roundup, which matters in shop work where the broken fastener might be a small socket screw one day and a large stud the next. The hex head format also means the extractor can be turned with hand tools in tight quarters where a drill will not fit. If your broken fasteners tend to be larger, harder, or seated in equipment rather than furniture, this is the set built around that kind of work.
Specs
- Set contents: 25 pieces, hex head multi-spline extractors
- Size range: 1/8 inch to 7/8 inch
- Material: high carbon steel
- Design: aggressive left hand spiral for high-torque applications
- Intended fasteners: broken studs, bolts, socket screws, and fittings
- Item weight: 16 ounces
- Model number: 53227
Alden 8440P Pro Grabit Broken Bolt and Damaged Screw Extractor 4-Piece Kit
The Alden Grabit Pro takes the two steps of extraction and folds them into a single bit. Each of the four dual-ended bits has a burnishing tip on one end that prepares the damaged screw or bolt head, and a threaded tip on the other end that grips and extracts it, so removal takes two steps with one tool in a 3/8 inch drill rather than a separate drill bit and extractor. The bits are sized by number: bit 1 handles No. 4 to No. 7 screws and No. 10 bolts (5mm), bit 2 handles No. 8 to No. 10 screws and 1/4 inch bolts (6mm), bit 3 handles No. 11 to No. 14 screws and 5/16 inch bolts (8mm), and bit 4 handles No. 16 to No. 24 screws and 3/8 inch bolts (10mm). The listing states the kit works on Phillips, Slotted, Hex, Torx, Tri-Wing, Pozidriv, and Fearson heads, plus most tamper-resistant screws, and that the serrated extracting end delivers greater torque for hard to remove fasteners. The kit is made in the USA and comes in a black poly case, with a 90 day limited warranty printed in the listing.
Specs
- Set contents: 4 dual-ended bits (burnishing tip and threaded tip)
- Coverage: screws No. 4 to No. 24; bolts No. 10 to 3/8 inch (5mm to 10mm)
- Compatible heads: Phillips, Slotted, Hex, Torx, Tri-Wing, Pozidriv, Fearson, most tamper-resistant screws
- Case: black poly case
- Item weight: 3.84 ounces
- Item dimensions: 8 x 4 x 1 inches
- Warranty: 90 day limited warranty
Topec Bolt Extractor Set, 10-Piece Lug Nut Remover Socket Tool (T8031)
Most extractors work from inside the fastener. This Topec set works from the outside, which is the right answer when the problem is a rounded-off bolt head, a damaged lug nut, or a wheel lock with no key. The ten sockets use an internal reverse spiral flute design that grips the outside of stripped, damaged, rounded, or rusted screws, bolts, and lug nuts as the socket turns. The listing states each socket is precision CNC-machined from chrome molybdenum steel to a hardness of 60HRC, with a black phosphate coating, and the set runs on a standard 1/2 inch square drive with a hex adapter, so it works with impact wrenches, pneumatic ratchets, breaker bars, and hand tools. The included components list extractor sockets in 14mm, 16mm, 17mm, 19mm, and 21mm sizes among the ten pieces, which covers the lug nut sizes most passenger vehicles use. The listing also prints a manufacturer warranty of one year from the date of purchase.
Specs
- Set contents: 10 pieces, bolt and lug nut extractor sockets
- Material: chrome molybdenum steel with black phosphate coating
- Hardness: 60HRC
- Drive: 1/2 inch square drive with hex adapter
- Socket sizes listed: 14mm, 16mm, 17mm, 19mm, and 21mm extractors among the set
- Item weight: 3.4 pounds
- Warranty: manufacturer warranty for 1 year from date of purchase
Topec 5-Piece Spiral Type Deep Extractor Set (RE-5-L)
Some fasteners do not break at the surface. They snap below it, down a hole, inside a fitting, or at the bottom of a spark plug well, where a standard tapered extractor cannot reach far enough to bite. This Topec set is built for that problem: five spiral type deep extractors in chrome molybdenum steel, made to remove deeply trapped and broken bolts, studs, fittings, threaded pipes, and pins, and sold as a spark plug easy-out set. The deep spiral form keeps the flutes engaged along a longer section of the fastener, which helps when the broken piece sits recessed and the extractor has to work deep in a bore. At 65 millimeters in item length and 100 grams in item weight, it is a compact kit that takes little room in a toolbox drawer next to a larger general set.
Specs
- Set contents: 5 pieces, spiral type deep extractors
- Material: chrome molybdenum steel
- Intended fasteners: deeply trapped and broken bolts, studs, fittings, threaded pipes, and pins
- Item length: 65 millimeters
- Item weight: 100 grams
- Model number: RE-5-L
- Set name as printed: Spiral Type Deep Extractor Set (5-Piece)
How to Choose
Start with where the fastener broke. If the head stripped but the shank is intact, a dual-ended drill-and-extract bit like the Alden Grabit Pro is the fastest route, because one tool prepares the head and pulls the screw without a separate pilot bit. If the fastener snapped off and left a stud or a broken bolt in a hole, you need the drill-and-extract sequence: a left hand drill bit to open a pilot hole, then a spiral flute or multi-spline extractor turned in reverse so it bites deeper as resistance builds. Sets like the IRWIN 11119 bundle both halves of that job, while the 25-piece multi-spline set trades the bundled bits for a wider size range and hex heads that a wrench can drive.
Next, check whether the damage is on the outside of the fastener instead. Rounded bolt heads, rusted nuts, and locking lug nuts cannot be helped by an internal extractor at all; they need an external grip socket like the Topec lug nut set, sized to the nut and driven on a 1/2 inch drive tool. Then consider depth. A fastener broken below the surface, inside a fitting or a plug well, calls for a deep extractor with enough length to reach it, such as the Topec spiral deep set.
Finally, match the steel and the size range to your work. Cobalt high speed steel suits hard metals and repeated drilling, high carbon steel suits high-torque turning, and chrome molybdenum steel is the wording used for impact sockets. Buy the size spread you will actually meet: four well-chosen sizes cover most household screws, while shop work with studs and fittings justifies a 25-piece range. Whatever set you pick, work in reverse, keep the drill speed low, and let the flutes bite rather than forcing the tool.
FAQ
Do screw extractors work on bolts that snapped off flush with the surface?
Yes, that is the job the drill-and-extract sets are made for. You drill a pilot hole into the center of the broken piece with a left hand drill bit, then turn the extractor into the hole in reverse. The spiral flutes or splines bite into the walls of the hole and back the broken piece out. The IRWIN 11119 set bundles the bits and extractors for this, and the 25-piece multi-spline set covers the same work across a wider size range.
What is the difference between spiral flute and multi-spline extractors?
A spiral flute extractor is a tapered tool with helical flutes that wedge into a drilled hole and grip harder as you turn. A multi-spline extractor has many straight splines along its body and a hex head, so it grips along the length of the hole and can be driven with a wrench or socket for higher torque.
Can these tools remove a rounded lug nut or a wheel lock without the key?
Internal extractors cannot, because there is no head left to drill into in the usual way. External extractor sockets can: the Topec T8031 set uses an internal reverse spiral flute inside each socket to grip the outside of damaged, rounded, or rusted lug nuts and bolts, and it runs on a standard 1/2 inch square drive with hand tools or an impact wrench.
How do dual-ended extractor bits like the Grabit Pro work?
Each bit has two working ends. One end is a burnishing tip that prepares the damaged screw or bolt head when run in a drill in reverse; you then flip the bit and the threaded tip grips the prepared head and extracts the fastener, also in reverse. The Alden 8440P listing states its four bits cover screws from No. 4 to No. 24 and bolts from No. 10 to 3/8 inch, and that the bits work in a 3/8 inch drill.
Conclusion
Every toolbox that sees real repair work eventually meets a fastener that will not turn. The five sets here cover the main ways out of that problem: the IRWIN 11119 for a matched drill-and-extract pairing in cobalt steel, the IRWIN 53227 multi-spline set for wide size coverage and high-torque studs and fittings, the Alden Grabit Pro for fast two-step removal of stripped screw heads, the Topec T8031 sockets for rounded bolts and lug nuts gripped from the outside, and the Topec deep spiral set for fasteners broken below the surface. Match the set to the break you meet most often, keep the drill in reverse and the speed low, and a ruined head becomes a pause in the job instead of the end of it.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Collect the home and kitchen items you want in one registry that guests can shop from.
Create a wedding registrySet up recurring deliveries of everyday items on eligible products. Terms and savings are set by Amazon.
Explore Subscribe & SaveFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAs an Amazon Associate we earn from qualifying purchases.




